- 您现在的位置：买卖IC网 > Sheet目录527 > SX1210I084T (Semtech)IC SINGLE-CHIP RECEIVER 32-TQFN
SX1210
ADVANCED COMMUNICATIONS & SENSING
7. Application Information
7.1. Crystal Resonator Specification
Table 28 shows the crystal resonator specification for the crystal reference oscillator circuit of the SX1210. This
specification covers the full range of operation of the SX1210 and is employed in the reference design (see section
7.5.3).
Table 28: Crystal Resonator Specification
Name
Fxtal
Cload
Rm
Co
Δ Fxtal
Δ Fxtal( Δ T)
Δ Fxtal( Δ t)
Description
Nominal frequency
Load capacitance for Fxtal
Motional resistance
Shunt capacitance
Calibration tolerance at 25+/-3°C
Stability over temperature range [-40°C ; +85°C]
Ageing tolerance in first 5 years
Min.
9
10
-
1
-15
-20
-2
Typ.
12.800
15
-
-
-
-
-
Max.
15
16.5
100
7
+15
+20
+2
Unit
MHz
pF
ohms
pF
ppm
ppm
ppm/year
Note that the initial frequency tolerance, temperature stability and ageing performance should be chosen in
accordance with the target operating temperature range and the receiver bandwidth selected.
7.2. Software for Frequency Calculation
The R1, P1, S1, and R2, P2, S2 dividers are configured over the SPI interface and programmed by 8 bits each, at
addresses 6 to 11. The frequency pairs may hence be switched in a single SPI cycle.
7.2.1. GUI
To aid the user with calculating appropriate R, P and S values, software is available to perform the frequency
calculation. The SX1210 PLL frequency Calculator Software can be downloaded from the Semtech website.
7.2.2. .dll for Automatic Production Bench
The Dynamically Linked Library (DLL) used by the software to perform these calculations is also provided, free of
charge, to users, for inclusion in automatic production testing. Key benefits of this are:
No hand trimming of the reference frequency required: the actual reference frequency of the Device Under Test
(DUT) can be easily measured (e.g. from the CLKOUT output of the SX1210) and the tool will calculate the
best frequencies to compensate for the crystal initial error.
Channel plans can be calculated and stored in the application’s memory, then adapted to the actual crystal
oscillator frequency.
7.3. Switching Times and Procedures
As an ultra-low power device, the SX1210 can be configured for low minimum average power consumption. To
minimize consumption the following optimized transitions between modes are shown.
Rev 2– Sept 8 , 2008
th
Page 57 of 73
www.semtech.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SX1211SK915
KIT STARTER FOR SX1211 915MHZ
SX1211SKA915
KIT STARTER FOR SX1211 915MHZ
SX1223SK868
KIT STARTER FOR XE1223 868MHZ
SX1231-31SKB915
TVS
SX1240SKA433
TVS
SX1701BI085TRT
IC AMP 2.5GHZ 5.3V 16-MLPQ
TA002-10002
LED HEATSINK W/FAN 12V 40X10MM
TC620HEPA
IC TEMP SNSR 5V DUAL TRIP 8-DIP
相关代理商/技术参数
SX1210I084TRT
制造商:Semtech Corporation 功能描述: 制造商:Semtech Corporation 功能描述:IC SINGLE-CHIP RECEIVER 32-TQFN 制造商:Semtech Corporation 功能描述:SX1210 Series 863 to 960 MHz 3 V 200 kbps Ultra Low Power Receiver - TQFN-32
SX1211
制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Lowest Power Integrated UHF Transceiver Short Range Devices
SX1211_08
制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Ultra-Low Power Integrated UHF Transceiver
SX1211-11SKA868
功能描述:KIT STARTER FOR SX1211 868MHZ RoHS:是 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796
SX1211-11SKA915
功能描述:KIT USB FOR SX1211 TXRX 915MHZ RoHS:是 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796
SX1211I084T
制造商:Semtech Corporation 功能描述:
SX1211I084TRT
功能描述:IC SNGL-CHIP TXRX 32-TQFN RoHS:是 类别:RF/IF 和 RFID >> RF 收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:30 系列:- 频率:4.9GHz ~ 5.9GHz 数据传输率 - 最大:54Mbps 调制或协议:* 应用:* 功率 - 输出:-3dBm 灵敏度:- 电源电压:2.7 V ~ 3.6 V 电流 - 接收:* 电流 - 传输:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 工作温度:-25°C ~ 85°C 封装/外壳:68-TQFN 裸露焊盘 包装:管件
SX1211I084TRT
制造商:Semtech Corporation 功能描述:GPSS WL SKU APP1